| INFINAM PA 6002 P |
PA12 powder for 3D printing / High toughness and softness / Excellent powder flow and recyclability / Fine surface detail / Food contact conformity / Melting point 187°C |
ADDITIVE MANUFACTURING (POWDER BED FUSION / SLS) |
|
| P84 TYPE 70 IN NMP |
Polyimide solution in NMP / Very high temperature resistance / Membranes and coatings |
Solution Processing (Membrane / Coating) |
|
| P84NT1 HCM SUPERFINE |
Polyimide powder (P84 NT) / Very high temperature resistance / Superfine powder |
Powder Processing (Direct Forming / Compression) |
|
| TROGAMID CARE MX73 |
Microcrystalline transparent polyamide, medical (Care) grade / Biocompatible (ISO 10993-1, USP Class VI) / High chemical and stress-crack resistance / BPA free / Gamma and EtO sterilisable / Drinking water contact |
Injection Moulding / Extrusion |
|
| TROGAMID CARE MX97 |
Microcrystalline transparent polyamide, medical (Care) grade / Biocompatible (ISO 10993-1, USP Class VI) / High chemical and stress-crack resistance / BPA free / Gamma and EtO sterilisable / UV resistant / Food contact |
Injection Moulding / Extrusion |
|
| TROGAMID CX 7323 NAT |
Microcrystalline, permanently transparent polyamide / High gloss / Excellent stress-crack and chemical resistance / HDT-A 108 C / Food and drinking water contact / UL yellow card |
Injection Moulding / Extrusion |
|
| TROGAMID CX9704 NC |
Amorphous transparent polyamide / Optical parts and lenses / Low haze (2%) / HDT-A 102 C / UL 94 HB / GWFI 960 C |
Injection Moulding |
|
| TROGAMID MY CX |
Transparent polyamide (myCX) / High toughness and chemical resistance |
Injection Moulding |
|
| TROGAMID MYCX HIGH FLOW |
Transparent polyamide (myCX) / High flow |
Injection Moulding |
|
| VESTAMID CARE ML21 |
PA12, medical (Care) grade / Resistant to body fluids / Biocompatible |
Injection Moulding / Extrusion |
|
| VESTAMID CW1412 NC |
Medium viscosity / Heat and UV stabilised / Cable co-extrusion / Low melting point (about 178 C), wide processing window / Low friction / Tensile modulus 1500 MPa |
Extrusion |
|
| VESTAMID D16 |
Medium viscosity PA612 resin / Low moisture absorption / Monofilaments (toothbrush bristles) / Food contact conformity |
Extrusion / Injection Moulding |
|
| VESTAMID DX9303 BK E70288 |
PA612 compound / High viscosity (MVR 11) / Plasticised / Impact modified / Heat and light stabilised / Melting point 211 C / Engine compartment tubing, higher pressure rating than PA12 above 100 C / Passes SAE J844 cold impact |
Extrusion |
|
| VESTAMID DX9304 BK E70238 |
PA612 compound / High viscosity (MVR 7) / Impact modified / Heat and light stabilised / Melting point 213 C (about 35 C above PA11/PA12) / Tubing for high burst pressure at high temperature (e.g. hydraulic clutch lines) |
Extrusion |
|
| VESTAMID DX9325 BK E70352 |
PA12 based compound / Chemical resistant / Low moisture absorption |
Injection Moulding / Extrusion |
|
| VESTAMID E40-S3 NAT S 25/1000 |
PEBA elastomer (PA12 + polyether blocks) / Heat, UV and light stabilised / Good low-temperature impact / Sports shoe soles |
Injection Moulding / Profile Extrusion |
|
| Vestamid E55-S3 NATURAL |
PEBA elastomer (PA12 + polyether blocks) / Shore 55D / Heat and light stabilised / No migrating plasticiser / Good low-temperature impact / Sports shoe soles |
Injection Moulding / Profile Extrusion |
|
| VESTAMID E62-S3 |
PEBA elastomer (PA12 + polyether blocks) / Shore 62D / Heat and light stabilised / No migrating plasticiser / Good low-temperature impact / Sports shoe soles |
Injection Moulding / Profile Extrusion |
|
| VESTAMID L-GF30 NC |
30% glass fibre reinforced / Heat stabilised / High stiffness (tensile modulus 6800 MPa) / HDT-A 165 C / Low moisture absorption / UL 94 HB |
Injection Moulding |
|
| VESTAMID L1670 |
Low viscosity / Heat and light stabilised / Thin wire insulation and cable jacketing / Low friction / Termite and rodent resistant / GWFI 960 C |
Extrusion |
|
| VESTAMID L1723 BK 9.7624 |
Low viscosity (MVR 160) / Plasticised / Heat and light stabilised / Easy release / Cable ties and strip clips / UL 94 HB (yellow card) |
Injection Moulding |
|
| VESTAMID L1833 BK 9.7623 |
23% glass fibre reinforced / Heat and UV stabilised / Medium viscosity / Easy release, short cycle times / HDT-A 160 C / CTI 600 / UL 94 HB |
Injection Moulding |
|
| VESTAMID L1833 NC |
23% glass fibre reinforced / Heat stabilised / Medium viscosity / Easy release, short cycle times / HDT-A 160 C / CTI 600 / UL 94 HB |
Injection Moulding |
|
| VESTAMID L1930 BK 9.7503 |
30% milled glass fibre reinforced / Heat stabilised / Low warpage, low shrinkage (0.5%) for precision parts / HDT-A 130 C / Fuel, oil and grease resistant / UL 94 HB |
Injection Moulding |
|
| VESTAMID L1940 BK 9.7504 |
Medium viscosity / Heat stabilised / Wire insulation, fibre optic and cable sheathing / Low friction / Food contact conformity |
Extrusion / Injection Moulding |
|
| VESTAMID L1940 NC |
Medium viscosity / Heat stabilised / Wire insulation and cable sheathing / Low friction / UL 94 HB (yellow card) |
Extrusion / Injection Moulding |
|
| VESTAMID L2140 BK 9.7504 |
High viscosity (MVR 6) / Heat and light stabilised / Tubing and fuel lines (DIN 73378 PA12-HL) / Low friction / Fuel and chemical resistant / UL 94 HB |
Extrusion |
|
| VESTAMID L2140 NATURAL |
High viscosity (MVR 3 at 220 C) / Heat and light stabilised / Tubing and fuel lines (DIN 73378 PA12-HL) / Low friction / Fuel and chemical resistant / UL 94 HB (yellow card) |
Extrusion |
|
| VESTAMID L2170 OR E20005 |
High viscosity (MVR 3.4) / Heat and light stabilised / Cable sheathing, tubes, rods and profiles / Low friction / Termite and rodent resistant / UL 94 HB (yellow card) / Orange |
Extrusion |
|
| VESTAMID LX9041 BK 9.7504 |
Medium viscosity (MVR 17) / Heat and UV stabilised / Black / Excellent adhesion to steel / High impact and abrasion resistance / For corrosion-protection coating of steel tubes |
EXTRUSION COATING |
|
| VESTAMID LX9102 BK |
PA12 based compound / Chemical resistant / Low moisture absorption |
Injection Moulding / Extrusion |
|
| VESTAMID NRG 2101 YELLOW |
High molecular weight PA12 / Gas distribution pipes at higher pressure and larger diameter (metal replacement) / MRS 18 MPa / High slow crack growth and RCP resistance / Yellow |
Extrusion |
|
| VESTAMID NRG 2902 BK |
High viscosity / Heat and UV stabilised / Nucleated, easy release, short cycle / Gas pipe fittings |
Injection Moulding |
|
| VESTAMID TERRA DS16 NC |
Bio-based polyamide (PA1010 type) / Low moisture absorption / Good chemical resistance |
Injection Moulding / Extrusion |
|
| VESTAMID X 7293 NC |
Plasticised PA12 compound / Flexible tubing and hose (DIN 73378 PA12-HIPHL Type 1) / Tensile modulus 400 MPa / High impact at low temperature |
Extrusion |
|
| VESTAMID X7070 |
Plasticised / Heat and light stabilised / Flexible automotive tubing and hose (DIN 73378 PA12-HIPHL Type 3, SAE J844) / Tensile modulus 370 MPa / High impact at low temperature |
Extrusion |
|
| VESTAMID X7099 |
PA612, glass fibre reinforced / Bonds directly to rubber (XNBR, HNBR, AEM, FPM) without adhesive / Excellent fuel, oil and grease resistance / Lower water absorption than PA6 and PA66 / Heat stabilised, HDT 190°C |
INJECTION MOULDING (K&K PLASTIC-RUBBER COMPOSITE PROCESS) |
|
| VESTAMID X7166 |
Low viscosity (MVR 108) / Halogen and phosphorus free flame retardant, UL94 V-2 at 0.8 mm / Heat stabilised / CTI 600 / For electronics and cable industry |
INJECTION MOULDING / WIRE EXTRUSION COATING |
|
| VESTAMID X7167 |
High viscosity (MVR 4) / Halogen and phosphorus free flame retardant, UL94 V-2 / Meets FAR 25.853 and ABD 0031 / For aircraft, railway and ship interiors / Heat stabilised / CTI 600 |
EXTRUSION / INJECTION MOULDING |
|
| VESTAMID X7293 BK 9 7507 |
Plasticised PA12 compound / Flexible tubing and hose (DIN 73378 PA12-HIPHL Type 1) / Tensile modulus 400 MPa / High impact at low temperature |
Extrusion |
|
| VESTAMID X7393 BK 9.7507 |
High viscosity (MVR 8) / Plasticised / Impact modified / Heat and light stabilised / Semi-rigid tubing with higher burst pressure (DIN 73378, DIN 74324 PA12-PHLY) / Brake fluid and fuel resistant / UL 94 HB |
Extrusion |
|